Coordinated Companies
AS 9100 Aerospace

08 | Crosby Lifting Hardware

Download PDF Version | Table of Contents

Crosby Lifting Hardware

Engineering Excellence

The majority of Crosby’s products are “Heat Treated.” The “Heat Treatment” allows the product to deform if overloading occurs, giving warning before ultimate failure. An “As-Forged,” or non- heat treated product, will break with little or no warning. This is called a catastrophic failure, and is a result of brittleness or lack of toughness in the non-heat treated product as compared to the "Heat Treated" product.

Quality Control

The majority of steel purchased by Crosby is isolated from production until approved by their metallurgical lab. Each product is individually “Pic Coded” (Product Identification Code) to allow traceability to its respective date of production and material certification.

Durability

Crosby’s products are manufactured with the highest design factors in the industry. Crosby’s products are better able to withstand abusive field conditions because of the improved impact and fatigue characteristics designed into each item of the line. Crosby recognizes the importance of all four of these essential properties in its products.

  • Working Load Limit
  • Ductility
  • Fatigue
  • Toughness
Recognized Dependability

Crosby is considered the standard of the industry both nationally and internationally. This can be drawn from the fact that most contracts involving rigging products, in the U.S. and around the world, read “Crosby Only” or “Crosby or Equal.”

The products in this section represent what we feel are the finest rigging hardware in the world stocked and sold by the Coordinated Companies statewide.

Go to www.coordinatedcompanies.com to view the full line of rigging hardware and products.

Forged Wire Rope Clips

  • Each base has a Product Identification Code (PIC) for material traceability, the name CROSBY or CG, and a size forged into it.
  • Based on the catalog breaking strength of wire rope, Crosby wire rope clips have an efficiency rating of 80% for 1/8" - 7/8" sizes, and 90% for sizes 1" through 3-1/2".
  • Entire Clip-Galvanized to resist corrosive and rusting action.
  • Sizes 1/8" through 2-1/2" and 3" have forged bases.
  • All Clips are individually bagged or tagged with proper application instructions and warning information.
  • Clip sizes up through 1-1/2" have rolled threads.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Look for the Red-U-Bolt®, your assurance of Genuine Crosby Clips.

Crosby Clips, all sizes 1/4" and larger, meet the performance requirements of Federal Specification FF-C-450 TYPE 1 CLASS 1, except for those provisions required of the contractor.

G-450 Crosby® Clips

Rope Size Dimensions (in.)
(in.) (mm) G-450 Stock No. Std. Package Qty. Weight Per 100 (lbs.) A B C D E F G H
1/8* 3-4* 1010015 100 6 .22 .72 .44 .47 .37 .38 .81 .99
3/16* 5* 1010033 100 10 .25 .97 .56 .59 .50 .44 .94 1.18
1/4 6-7 1010051 100 19 .31 1.03 .50 .75 .66 .56 1.19 1.43
5/16 8 1010079 100 28 .38 1.38 .75 .88 .73 .69 1.31 1.66
3/8 9-10 1010097 100 48 .44 1.50 .75 1.00 .91 .75 1.63 1.94
7/16 11 1010113 50 78 .50 1.88 1.00 1.19 1.13 .88 1.91 2.28
1/2 12-13 1010131 50 80 .50 1.88 1.00 1.19 1.13 .88 1.91 2.28
9/16 14-15 1010159 50 109 .56 2.25 1.25 1.31 1.34 .94 2.06 2.50
5/8 16 1010177 50 110 .56 2.25 1.25 1.31 1.34 .94 2.06 2.50
3/4 18-20 1010195 25 142 .62 2.75 1.44 1.50 1.39 1.06 2.25 2.84
7/8 22 1010211 25 212 .75 3.12 1.62 1.75 1.58 1.25 2.44 3.16
1 24-26 1010239 10 252 .75 3.50 1.81 1.88 1.77 1.25 2.63 3.47
1-1/8 28-30 1010257 10 283 .75 3.88 2.00 2.00 1.91 1.25 2.81 3.59
1-1/4 32-34 1010275 10 438 .88 4.44 2.22 2.31 2.17 1.44 3.13 4.13
1-3/8 36 1010293 10 442 .88 4.44 2.22 2.38 2.31 1.44 3.13 4.19
1-1/2 38 1010319 10 544 .88 4.94 2.38 2.59 2.44 1.44 3.41 4.44
1-5/8 41-42 1010337 Bulk 704 1.00 5.31 2.62 2.75 2.66 1.63 3.63 4.75
1-3/4 44-46 1010355 Bulk 934 1.13 5.75 2.75 3.06 2.92 1.81 3.81 5.24
2 48-52 1010373 Bulk 1300 1.25 6.44 3.00 3.38 3.28 2.00 4.44 5.88
2-1/4 56-58 1010391 Bulk 1600 1.25 7.13 3.19 3.88 3.19 2.00 4.56 6.38
2-1/2 62-65 1010417 Bulk 1900 1.25 7.69 3.44 4.13 3.69 2.00 4.05 6.63
** 2-3/4 ** 68-72 1010435 Bulk 2300 1.25 8.31 3.56 4.38 4.88 2.00 5.00 6.88
3 75-78 1010453 Bulk 3100 1.50 9.19 3.88 4.75 4.44 2.38 5.31 7.61
** 3-1/2 ** 85-90 1010426 Bulk 4000 1.50 10.75 4.50 5.50 6.00 2.38 6.19 8.38

* Electro-plated U-Bolt and Nuts. ** 2-3/4" and 3-1/2" base is made of cast steel.

  • Each base has a Product Identification Code (PIC) for material traceability, the name CROSBY or CG, and a size forged into it.
  • Entire Clip is made from 316 Stainless Steel to resist corrosive and rusting action.
  • All components are Electro-Polished.
  • All Clips are individually bagged or tagged with proper application instructions and warning information.

SS-450 Stainless Steel Wire Rope Clips

Rope Size Dimensions (in.)
(in.) (mm) SS-450 Stock No. Std. Package Qty. Weight Per 100 (lbs.) A B C D E F G H
1/8 3-4 1011250 Bulk 6 .22 .72 .44 .47 .41 .38 .81 .94
3/16 5 1011261 Bulk 10 .25 .97 .56 .59 .50 .44 .94 1.16
1/4 6-7 1011272 Bulk 20 .31 1.03 .50 .75 .66 .56 1.19 1.44
3/8 9-10 1011283 Bulk 47 .44 1.50 .75 1.00 .91 .75 1.63 1.94
1/2 12-13 1011305 Bulk 77 .50 1.88 1.00 1.19 1.13 .88 1.91 2.28
5/8 16 1011327 Bulk 106 .56 2.38 1.25 1.31 1.34 .94 2.06 2.50

Fast Grip® Wire Rope Clips

  • Entire clip is Galvanized to resist corrosive and rusting action.
  • Based on the catalog breaking strength of wire rope, Crosby wire rope clips have an efficiency rating of 80% for 3/16" - 7/8" sizes, and 90% for sizes 1" through 1-1/2".
  • Bolts are an integral part of the saddle. Nuts can be installed in such a way as to enable the operator to swing the wrench in a full arc for fast installation.
  • All sizes have forged steel saddles.
  • All Clips are individually bagged or tagged with proper application instructions and warning information.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Assembled with standard heavy hex nuts.

SS-450 Stainless Steel Wire Rope Clips

Rope Size Dimensions (in.)
(in.) (mm) G-429 Stock No. Std. Package Qty. Weight Per 100 (lbs.) C D E G N
3/16 - 1/4 5-7 1010471 100 23 .40 .94 .38 1.41 1.44
5/16 8 1010499 100 28 .47 1.06 .38 1.50 1.54
3/8 10 1010514 50 40 .51 1.06 .44 1.84 1.78
7/16 - 1/2 11-13 1010532 50 62 .59 1.25 .50 2.21 2.15
9/16 - 5/8 14-16 1010550 50 103 .72 1.50 .63 2.72 2.57
3/4 18-20 1010578 25 175 .86 1.81 .75 2.94 2.67
7/8 22 1010596 25 225 .97 2.12 .75 3.31 2.86
1 24-26 1010612 10 300 1.13 2.25 .75 3.72 3.06
1-1/8 28-30 1010630 10 400 1.28 2.38 .88 4.22 3.44
1-1/4 32-34 1010658 10 400 1.34 2.50 .88 4.25 3.56
1-3/8 - 1-1/2 36-40 1010676 Bulk 700 1.56 3.00 1.00 5.56 4.12

*Sizes through 5/8" incorporate New Style design.

Crosby® Screw Pin Shackles

  • Capacities 1/3 thru 55 metric tons
  • Forged - Quenched and Tempered, with alloy pins.
  • Working Load Limit permanently shown on every shackle.
  • Hot Dip galvanized or Self Colored.
  • Fatigue rated.
  • Shackles 25t and larger are RFID EQUIPPED.
  • Shackles can be furnished proof tested with certificates to designated standards, such as ABS, DNV, Lloyds, or other certification. Charges for proof testing and certification available when requested at the time of order.
  • Shackles are Quenched and Tempered and can meet DNV impact requirements of 42 joules at -20 C.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Look for the Red Pin® . . . the mark of genuine Crosby quality.
  • Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.
Stock No. Dimensions (in.) Tolerance +/-
Nominal Size (in.) Working Load Limit (t)* G-209 S-209 Weight Each (lbs.) A B C D E F G H L M P C A
3/16 1/3 1018357 - .06 .38 .25 .88 .19 .60 .56 .98 1.47 .16 1.14 .19 .06 .06
1/4 1/2 1018375 1018384 .10 .47 .31 1.13 .25 .78 .61 1.28 1.84 .19 1.43 .25 .06 .06
5/16 3/4 1018393 1018400 .19 .53 .38 1.22 .31 .84 .75 1.47 2.09 .22 1.71 .31 .06 .06
3/8 1 1018419 1018428 .31 .66 .44 1.44 .38 1.03 .91 1.78 2.49 .25 2.02 .38 .13 .06
7/16 1-1/2 1018437 1018446 .38 .75 .50 1.69 .44 1.16 1.06 2.03 2.91 .31 2.37 .44 .13 .06
1/2 2 1018455 1018464 .72 .81 .63 1.88 .50 1.31 1.19 2.31 3.28 .38 2.69 .50 .13 .06
5/8 3-1/4 1018473 1018482 1.37 1.06 .75 2.38 .63 1.69 1.50 2.94 4.19 .44 3.34 .69 .13 .06
3/4 4-3/4 1018491 1018507 2.35 1.25 .88 2.81 .75 2.00 1.81 3.50 4.97 .50 3.97 .81 .25 .06
7/8 6-1/2 1018516 1018525 3.62 1.44 1.00 3.31 .88 2.28 2.09 4.03 5.83 .50 4.50 .97 .25 .06
1 8-1/2 1018534 1018543 5.03 1.69 1.13 3.75 1.00 2.69 2.38 4.69 6.56 .56 5.13 1.06 .25 .06
1-1/8 9-1/2 1018552 1018561 7.41 1.81 1.25 4.25 1.16 2.91 2.69 5.16 7.47 .63 5.71 1.25 .25 .06
1-1/4 12 1018570 1018589 9.50 2.03 1.38 4.69 1.29 3.25 3.00 5.75 8.25 .69 6.25 1.38 .25 .06
1-3/8 13-1/2 1018598 1018605 13.53 2.25 1.50 5.25 1.42 3.63 3.31 6.38 9.16 .75 6.83 1.50 .25 .13
1-1/2 17 1018614 1018623 17.20 2.38 1.63 5.75 1.54 3.88 3.63 6.88 10.00 .81 7.33 1.62 .25 .13
1-3/4 25 1018632 1018641 27.78 2.88 2.00 7.00 1.84 5.00 4.19 8.86 12.34 1.00 9.06 2.25 .25 .13
2 35 1018650 1018669 45.00 3.25 2.25 7.75 2.08 5.75 4.81 9.97 13.68 1.22 10.35 2.40 .25 .13
2-1/2 55 1018678 1018687 85.75 4.13 2.75 10.50 2.71 7.25 5.69 12.87 17.84 1.38 13.00 3.13 .25 .25

* NOTE: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working Load Limit

Stock No. Dimensions (in.) Tolerance +/-
Nominal Size (in.) Working Load Limit (t)* G-210 S-210 Weight Each (lbs.) A B C D E F G K L M G A
1/4 1/2 1019150 1019169 .11 .47 .31 .25 .25 .97 .62 .97 1.59 .19 1.43 .06 .06
5/16 3/4 1019178 1019187 .17 .53 .38 .31 .31 1.15 .75 1.07 1.91 .22 1.71 .06 .06
3/8 1 1019196 1019203 .28 .66 .44 .38 .38 1.42 .92 1.28 2.31 .25 2.02 .13 .06
7/16 1-1/2 1019212 1019221 .43 .75 .50 .44 .44 1.63 1.06 1.48 2.67 .31 2.37 .13 .06
1/2 2 1019230 1019249 .59 .81 .63 .50 .50 1.81 1.18 1.66 3.03 .38 2.69 .13 .06
5/8 3-1/4 1019258 1019267 1.25 1.06 .75 .63 .63 2.32 1.50 2.04 3.76 .44 3.34 .13 .06
3/4 4-3/4 1019276 1019285 2.63 1.25 .88 .81 .75 2.75 1.81 2.40 4.53 .50 3.97 .25 .06
7/8 6-1/2 1019294 1019301 3.16 1.44 1.00 .97 .88 3.20 2.10 2.86 5.33 .50 4.50 .25 .06
1 8-1/2 1019310 1019329 4.75 1.69 1.13 1.00 1.00 3.69 2.38 3.24 5.94 .56 5.13 .25 .06
1-1/8 9-1/2 1019338 1019347 6.75 1.81 1.25 1.25 1.13 4.07 2.69 3.61 6.78 .63 5.71 .25 .06
1-1/4 12 1019356 1019365 9.06 2.03 1.38 1.38 1.25 4.53 3.00 3.97 7.50 .69 6.25 .25 .13
1-3/8 13-1/2 1019374 1019383 11.63 2.25 1.50 1.50 1.38 5.01 3.31 4.43 8.28 .75 6.83 .25 .13
1-1/2 17 1019392 1019409 15.95 2.38 1.63 1.62 1.50 5.38 3.62 4.84 9.05 .81 7.33 .25 .13
1-3/4 25 1019418 1019427 26.75 2.88 2.00 2.12 1.75 6.38 4.19 5.78 10.97 1.00 9.06 .25 .13
2 35 1019436 1019445 42.31 3.25 2.25 2.36 2.10 7.25 5.00 6.77 12.74 1.13 10.35 .25 .13
2-1/2 55 1019454 1019463 71.75 4.12 2.75 2.63 2.63 9.38 5.68 8.07 14.85 1.38 13.00 .25 .25

* NOTE: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Strength is 6 times the Working Load Limit.

Crosby® Bolt Type Shackles

  • Capacities 1/3 thru 150 metric tons.
  • Working Load Limit permanently shown on every shackle.
  • Forged - Quenched and tempered, with alloy pins.
  • Hot Dip galvanized or Self Colored.
  • Fatigue rated (1/3t - 55t).
  • Shackles 25t and larger are RFID EQUIPPED
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed buy ASME B30.26.
  • Shackles 55 metric tons and smaller can be furnished proof tested with certificates to designated standards, such as ABS, DNV, Lloyds, or other certification when requested at time of order.
  • Shackles 85 metric tons and larger can be provided as follows:
    • Non Destructive Tested
    • Serialized Pin and Bow
    • Material Certification (Chemical) Certification must be requested at time of order
  • Look for the Red Pin® . . . the mark of genuine Crosby quality.
  • Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes
Stock No. Dimensions (in.) Tolerance +/-
Nominal Size (in.) Working Load Limit (t)* G-2130 S-2130 Weight Each (lbs.) A B C D E F H L N C A
3/16 1/3 ‡ 1019464 - .06 .38 .25 .88 .19 .60 .56 1.47 .98 .19 .06 .06
1/4 1/2 1019466 - .11 .47 .31 1.13 .25 .78 .61 1.84 1.28 .25 .06 .06
5/16 3/4 1019468 - .22 .53 .38 1.22 .31 .84 .75 2.09 1.47 .31 .06 .06
3/8 1 1019470 - .33 .66 .44 1.44 .38 1.03 .91 2.49 1.78 .38 .13 .06
7/16 1-1/2 1019471 - .49 .75 .50 1.69 .44 1.16 1.06 2.91 2.03 .44 .13 .06
1/2 2 1019472 1019481 .76 .81 .64 1.88 .50 1.31 1.19 3.28 2.31 .50 .13 .06
5/8 3-1/4 1019490 1019506 1.68 1.06 .77 2.38 .63 1.69 1.50 4.19 2.94 .69 .13 .06
3/4 4-3/4 1019515 1019524 2.72 1.25 .89 2.81 .75 2.00 1.81 4.97 3.50 .81 .25 .06
7/8 6-1/2 1019533 1019542 3.95 1.44 1.02 3.31 .88 2.28 2.09 5.83 4.03 .97 .25 .06
1 8-1/2 1019551 1019560 5.66 1.69 1.15 3.75 1.00 2.69 2.38 6.56 4.69 1.06 .25 .06
1-1/8 9-1/2 1019579 1019588 8.27 1.81 1.25 4.25 1.13 2.91 2.69 7.47 5.13 1.25 .25 .06
1-1/4 12 1019597 1019604 11.71 2.03 1.40 4.69 1.29 3.25 3.00 8.25 5.75 1.38 .25 .06
1-3/8 13-1/2 1019613 1019622 15.83 2.25 1.53 5.25 1.42 3.63 3.31 9.16 6.38 1.50 .25 .13
1-1/2 17 1019631 1019640 19.00 2.38 1.66 5.75 1.53 3.88 3.63 10.00 6.88 1.62 .25 .13
1-3/4 25 1019659 1019668 33.91 2.88 2.04 7.00 1.84 5.00 4.19 12.34 8.80 2.25 .25 .13
2 35 1019677 1019686 52.25 3.25 2.30 7.75 2.08 5.75 4.81 13.68 10.15 2.40 .25 .13
2-1/2 55 1019695 1019702 98.25 4.13 2.80 10.50 2.71 7.25 5.69 17.90 12.75 3.13 .25 .25
3 † 85 1019711 - 154.00 5.00 3.30 13.00 3.12 7.88 6.50 21.50 14.62 3.62 .25 .25
3-1/2 † 120 ‡ 1019739 - 265.00 5.25 3.76 14.63 3.62 9.00 8.00 24.88 17.02 4.38 .25 .25
4 † 150 ‡ 1019757 - 338.00 5.50 4.26 14.50 4.00 10.00 9.00 25.68 18.00 4.56 .25 .25
Stock No. Dimensions (in.) Tolerance +/-
Nominal Size (in.) Working Load Limit (t)* G-2130 S-2150 S-2150 Weight Each (lbs.) A B D F K M P R G A
1/4 1/2 1019768 - .13 .47 .31 .25 .62 .91 1.59 .97 1.56 .25 .06 .06
5/16 3/4 1019770 - .23 .53 .38 .31 .75 1.07 1.91 1.15 1.82 .31 .06 .06
3/8 1 1019772 - .33 .66 .44 .38 .92 1.28 2.31 1.42 2.17 .38 .13 .06
7/16 1-1/2 1019774 - .49 .75 .50 .44 1.06 1.48 2.67 1.63 2.51 .44 .13 .06
1/2 2 1019775 1019784 .75 .81 .64 .50 1.18 1.66 3.03 1.81 2.80 .50 .13 .06
5/8 3-1/4 1019793 1019800 1.47 1.06 .77 .63 1.50 2.04 3.76 2.32 3.56 .63 .13 .06
3/4 4-3/4 1019819 1019828 2.25 1.25 .89 .75 1.81 2.40 4.53 2.75 4.15 .81 .25 .06
7/8 6-1/2 1019837 1019816 3.85 1.44 1.02 .88 2.10 2.86 5.33 3.20 4.82 .97 .25 .06
1 8-1/2 1019855 1019864 5.55 1.69 1.15 1.00 2.38 3.24 5.94 3.69 5.39 1.00 .25 .06
1-1/8 9-1/2 1019873 1019882 7.60 1.81 1.25 1.13 2.68 3.61 6.78 5.07 5.90 1.25 .25 .06
1-1/4 12 1019891 1019908 10.81 2.03 1.40 1.25 3.00 3.97 7.50 4.53 6.69 1.38 .25 .06
1-3/8 13-1/2 1019917 1019926 13.75 2.25 1.53 1.38 3.31 4.43 8.28 5.01 7.21 1.50 .25 .13
1-1/2 17 1019935 1019944 18.50 2.38 1.66 1.50 3.62 4.87 9.05 5.38 7.73 1.62 .25 .13
1-3/4 25 1019953 1019962 31.40 2.88 2.04 1.75 4.19 5.82 10.97 6.38 9.33 2.12 .25 .13
2 35 1019971 1019980 46.75 3.25 2.30 2.10 5.00 6.82 12.74 7.25 10.41 2.36 .25 .13
2-1/2 55 1019999 1020004 85.00 4.12 2.80 2.63 5.68 8.07 14.85 9.38 13.58 2.63 .25 .25
3 † 85 1020013 - 124.25 5.00 3.25 3.00 6.50 8.56 16.87 11.00 15.13 3.50 .25 .25

Crosby® Alloy Bolt Type Shackles

  • Quenched and Tempered.
  • Alloy bows, Alloy bolts.
  • Forged Alloy Steel 30 thru 175 metric tons. Cast Alloy Steel 200 thru 400 metric tons.
  • Working Load Limit is permanently shown on every shackle.
  • All sizes are individually proof tested to 2.0 times the Working Load Limit.
  • Pins are galvanized and painted red.
  • All sizes are RFID EQUIPPED.
  • Shackles are Quenched and Tempered and can meet DNV impact requirements of 42 joules at -20 C.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Shackles 200 metric tons and larger are provided as follows.
    • Serialized Pin and Bow
    • Material Certification (Chemical)
    • Magnetic Particle Inspected.
    • Certification must be requested at time of order.
  • Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.
Stock No. Dimensions (in>) Tolerance +/-
Nominal Shackle Size (in.) Working Load Limit (t)* G-2140 S-2140 Weight Each (lbs.) A B C D E F G H J K L A E
1-1/2 30 1021110 1021129 18.8 2.38 3.62 1.62 1.63 5.75 1.39 6.88 7.73 10.00 3.88 1.53 .13 .25
1-3/4 40 1021138 1021147 33.9 2.88 4.19 2.25 2.00 7.00 1.75 8.81 9.33 12.34 5.00 1.84 .13 .25
2 55 1021156 1021165 52.0 3.25 4.81 2.40 2.25 7.75 2.00 10.16 10.41 13.68 5.75 2.08 .13 .25
2-1/2 85 1021174 1021183 96.0 4.12 5.81 3.12 2.75 10.50 2.62 12.75 13.58 17.90 7.25 2.71 .25 .25
3 120 1021192 178.0 5.00 6.50 3.63 3.25 13.00 3.00 14.62 15.13 21.50 7.88 3.12 .25 .25
3-1/2 † 150 1021218 265.0 5.25 8.00 4.38 3.75 14.63 3.75 17.02 17.62 24.88 9.00 3.62 .25 .25
4 † 175 1021236 338.0 5.50 9.00 4.56 4.25 14.50 4.00 18.00 20.37 25.68 10.00 4.00 .25 .25
4-3/4** † 200 1021414 450.0 7.25 10.50 6.00 4.75 15.63 3.75 21.00 21.21 29.25 11.00 4.50 .25 .25
5** † 250 1021432 600.0 8.50 12.00 6.50 5.00 20.00 3.88 24.50 22.68 35.00 13.00 4.50 .25 .25
6** † 300 1021450 775.0 8.38 12.00 6.75 6.00 19.50 4.75 25.00 25.06 35.25 13.00 5.00 .25 .25
7** † 400 1021478 1102.0 8.25 14.00 7.25 7.00 22.50 6.50 26.00 28.68 40.25 13.00 6.00 .25 .25

* Note: Maximum Proof Load is 2.0 times the Working Load Limit. Minimum Ultimate Load is 4 times the Working Load Limit on 200 thru 400 metric Tons.
For sizes 30 thru 175 metric Tons, Minimum Ultimate Load is 5.4 times the Working Load Limit.
** Cast Alloy Steel.
† Furnished with Round Head Bolts with welded handle.

Sling Saver Web Sling Shackles

  • All Alloy Construction
  • Design Factor of 5 to 1.
  • Each shackle has a Product Identification Code (PIC) for material traceability along with a Working Load Limit and the name Crosby forged into it.
  • Incorporates same ear spread and pin dimensions as conventional Crosby Shackles. Allows easy connection to pad eyes, eye bolts, and lifting lugs.
  • Increased radius of bow gives wider sling bearing surface resulting in an increased area for load distribution, thus:
    • Increasing Synthetic Sling efficiency as compared to standard anchor and chain shackle bows and conventional eye hooks. This allows 100% of the slings rated Working Load Limit to be achieved.
    • Allows better load distribution on internal fibers.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Look for the Red Pin® ... The mark of genuine Crosby Quality.
Web Slings*
Round Slings Size (No.) Webbing Width (in.) Eye Width (in.) Ply Working Load Limit (Tons)† S-281 Stock No. Weight Each (lbs.) A C D E K M N
1 & 2 2 2 2 3-1/4 1021048 1.2 1.06 2.50 .75 1.62 1.22 3.84 3.34
3 3 1.5 2 4-1/2 1021057 1.5 1.25 2.00 .88 1.50 1.41 3.38 3.97
4 4 2 2 6-1/4 1021066 2.5 1.44 2.50 1.00 2.00 1.62 4.22 4.50
5 & 6 6 3 2 8-1/2 1021075 4.3 1.69 3.62 1.13 2.75 1.84 5.64 5.13

* NOTE: Designed for use with Type III, (Eye & Eye). Class 7, 2 Ply web slings. For 3" and larger webbing width, tapered eye is required. † Maximum Proof Load is 2-1/2 times the Working Load Limit. Minimum Ultimate strength is 5 times the Working Load Limit.

Crosby Sling Saver hardware meets the requirements for minimum stock diameter of thickness, and effective contact width shown in the Recommend Standards Specification for Synthetic Polyester Round Slings by the Web Sling & Tie Down Association. WSTDA-RS1 (revised 2001)

  • All sizes Quenched and tempered for maximum strength.
  • Forged alloy steel from 7 through 300 metric tons.
  • Cast alloy steel from 400 through 1550 metric tons.
  • Sizes 300 metric tons and smaller are proof tested to 2 times the Working Load Limit.
  • Sizes 400 metric tons and larger are tested to 1.33 times Working Load Limit.
  • All ratings are in metric tons, embossed on side of bow.
  • G-2160, (7-55t), are Hot Dip Galvanized and pins are painted red.
  • G-2160, (75t and larger), bows are furnished Dimetcoted, and pins are Dimetcoted, then painted red.
  • S-2160 bows and pins are painted red.
  • Shackles, 30t and larger, are RFID EQUIPPED.
  • Greatly improves life of wire rope slings.
  • Can be used to connect HIGH STRENGTH Synthetic Web Slings, HIGH STRENGTH Synthetic Round Slings or Wire Rope Slings.
  • Increase in shackle bow radius provides minimum 58% gain in sling bearing surface and eliminates need for a thimble.
  • Increases usable sling strength minimum of 15%.
  • Pin is non-rotating, with weld-on handles for easier use (75t and larger).
  • All 2160 shackles are individually proof tested and magnetic particle inspected. Crosby certification available at time of order.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Shackles requiring ABS, Lloyds and other certifications are available upon special request and must be specified at time of order.
  • Shackles 18t and larger have DNV Type Approval to Rules for Certification of Lifting Appliances, and are produced in accordance with DNV MSA requirements. Databook is provided that includes required documents.
    • Serialization / Identification
    • Material Testing (Physical / Chemical / Charpy)
    • Proof Testing
Dimensions (in.)
Working Load Limit (t)* G-2160 Stock No. S-2160 Stock No. Weight Each (lbs.) A B +/- .25 C D +/- .02 E G H J K P R
7 1021256 1021548 4.0 4.14 1.25 .69 .88 1.82 1.25 3.56 1.60 1.25 4.10 5.87
12.5 1021265 1021557 10 5.38 1.69 .92 1.13 2.38 1.37 4.63 2.13 1.63 5.51 7.63
18 1021274 1021566 15 6.69 2.03 1.16 1.38 2.69 1.50 5.81 2.50 2.00 6.76 9.38
30 1021283 1021575 25 7.69 2.37 1.38 1.63 3.50 1.75 6.94 3.13 2.50 8.50 11.38
40 1021285 1021584 35 9.28 2.88 1.69 2.00 4.00 2.31 8.06 3.75 3.00 10.62 13.62
55 1021287 1021593 71 10.36 3.25 2.00 2.25 4.63 2.63 9.36 4.50 3.50 12.26 15.63
† 75 1021290 100 14.37 4.13 2.12 2.75 5.00 2.50 11.53 4.75 3.64 12.28 18.41
† 125 1021307 178 16.51 5.12 2.56 3.15 5.71 3.15 14.36 5.91 4.33 14.96 22.65
† 200 1021316 500 20.67 5.91 3.35 4.12 7.28 4.33 18.90 8.07 5.41 19.49 29.82
† 300 1021325 643 24.20 7.38 4.00 5.25 9.25 5.38 23.63 10.38 6.31 23.38 37.26
400 1021334 1165 30.27 8.66 5.16 6.30 11.81 6.30 22.64 12.60 7.28 27.17 38.78
500 1021343 1462 33.35 9.87 5.73 7.09 13.39 6.69 24.81 13.39 8.86 31.10 42.72
600 1021352 2155 36.02 10.83 6.23 7.87 15.50 7.28 27.56 14.57 9.74 34.06 47.24
700 1021361 2585 38.91 11.81 6.59 8.46 14.80 7.87 28.94 15.75 10.63 37.01 50.18
800 1021254 3075 41.66 12.80 7.30 9.06 16.54 8.27 29.53 16.54 10.92 38.39 52.09
900 1021389 3720 43.73 13.78 7.78 9.84 16.93 8.66 29.82 17.32 11.52 40.35 54.04
1000 1021370 4130 45.98 14.96 8.33 10.63 17.72 9.06 29.92 18.11 12.11 42.32 55.31
1250 1021272 6310 49.86 16.93 9.15 11.81 21.00 10.43 36.61 20.87 12.70 46.26 65.35
1550 1021281 8155 54.89 18.31 10.58 12.60 23.82 15.92 42.32 22.82 13.29 49.41 73.43

* 7t-300t Proof Load is 2 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.
400t-1550t Proof Load is 1.33 times the Working Load Limit. Ultimate Load is 4.5 times the Working Load Limit.
†Available in Forged and Cast Alloy Steel.

Crosby® Eye Hooks

All Crosby 320 Eye Hoist Hooks incorporate the following features:

  • The most complete line of Eye hoist hooks.
  • Available in carbon steel and alloy steel.
  • Designed with a 5:1 Design Factor for (Carbon Steel); 4:1 Design Factor for (Alloy Steel).
  • Eye hooks are load rated.
  • Proper design, careful forging and precision controlled quenched and tempering give maximum strength without excessive weight and bulk.
  • Every Crosby Eye Hook has a pre-drilled cam which can be equipped with a latch. Even years after purchase of the original hook, latch assemblies can be added.
  • Chemical analysis and tensile tests performed on each PIC to verify chemistry and mechanical properties.
  • Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.
  • Hoist hooks incorporate two types of strategically placed markings forged into the product which address two (2) QUIC-CHECK® features:
    • Deformation Indicators and Angle Indicators.

The following additional features have been incorporated in the new Crosby S-320N Eye Hoist Hooks. (Sizes 3/4 metric ton Carbon through 22 metric ton Alloy.)

  • Metric Rated at 5:1 Design Factor for (Carbon Steel); 4:1 Design Factor for (Alloy Steel).
  • Can be proof tested to 2-1/2 times the working Load Limit.
  • Low profile hook tip.
  • New integrated latch (S-4320) meets the World class standard for lifting.
    • Heavy duty stamped latch interlocks with the hook tip.
    • High cycle, long life spring.
    • When secured with proper cotter pin through the hole in the tip of hook, meets the intent of OSHA Rule 1926.550(g) for personnel hoisting.
  • Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
Working Load Limit (t)* Eye Hook Stock No. Replacement Latch Kits
Carbon Alloy Hook ID Code Carbon S-320C S-320CN S.C. Carbon G-320CN Galv. Alloy S-320A S-320AN S.C. Weight Each (lbs.) S-4320 stock No. PL Stock No. SS-4055 Stock No.
3/4 1 † D 1022200 1022208 1022375 .61 1096325
1 1-1/2 † F 1022211 1022219 1022386 .89 1096574
1-1/2 2 † G 1022222 1022230 1022397 1.44 1096421
2 3 † H 1022233 1022241 1022406 2.07 1096468
3 5 † I 1022244 1022249 1022419 4.30 1096515 1092000
5 7 † J 1022255 1022262 1022430 8.30 1096562 1092001
7-1/2 11 † K 1022264 1022274 1022441 15.00 1096609 1092002
10 15 † L 1022277 1022285 1022452 20.77 1096657 1092003
15 22 † N 1022288 1022296 1022465 39.50 1096704 1092004
20 30 O 1023289 1023546 60.00 1093716 1090161
25 37 P 1023305 1023564 105.00 1093717 1090189
30 45 S 1023323 1023585 148.00 1093718 1090189
40 60 T 1023341 1023608 228.00 1093719 1090205

* Eye Hooks (3/4 TC - 22TA), Proof load is 2.5 times Working Load Limit. Eye Hooks (20 TC - 60TA), Proof Load is 2 times Working Load Limit.
All carbon hooks-average straightening load (ultimate load) is 5 times Working Load Limit. Alloy eye hooks 1 ton through 22 ton-average
straightening load (ultimate load) is 5 times Working Load Limit. Alloy eye hooks 30 tons through 60 tons-average straightening load (ultimate load) is 4.5 times Working Load Limit.
† New 320N style hook.

  • Hoist hooks incorporate markings forged into the product which address two (2) QUIC-CHECK® features.
    • Deformation Indicators --Two strategically placed marks, one just below the shank or eye and the other on the hook tip, which allows for a QUIC-CHECK® measurement to determine if the throat opening has changed, thus indicating abuse or overload. To check, use a measuring device (i.e. tape measure) to measure the distance between the marks. The marks should align to either an inch or half-inch increment on the measuring device. If the measurement does not meet this criteria, the hook should be inspected fur- ther for possible damage.
    • Angle Indicators --Indicates the maximum included angle which is allowed between two (2) sling legs in the hook. These indicators also provide the opportunity to approximate other included angles between two sling legs.
Dimensions (in.)
Hook ID* C D F G J K M N O† O2†† Q T† T2†† AA
D 3.34 2.83 1.25 .73 .90 .63 .63 .36 .89 .75 .87 1.50
F 3.81 3.11 1.38 .84 .93 .71 .71 .42 .91 .91 .98 2.00
G 4.14 3.53 1.50 1.00 1.00 .88 .88 .55 1.00 1.13 1.03 2.00
H 4.69 3.97 1.63 1.13 1.13 .94 .94 .58 1.09 1.25 1.16 2.00
I 5.77 4.81 2.00 1.44 1.47 1.31 1.31 .72 1.36 1.00 1.56 1.53 1.50 2.50
J 7.37 6.27 2.50 1.81 1.75 1.66 1.66 .90 1.61 1.31 2.00 1.96 1.88 3.00
K 9.07 7.45 3.00 2.25 2.29 1.88 1.63 1.11 2.08 1.81 2.44 2.47 2.25 4.00
L 10.08 8.30 3.25 2.59 2.50 2.19 1.94 1.27 2.27 2.00 2.84 2.62 2.31 4.00
N 12.53 10.30 4.25 3.00 3.30 2.69 2.38 1.56 3.02 2.75 3.50 2.83 2.56 5.00
O 14.06 13.62 5.00 3.62 4.00 3.00 3.00 1.75 3.25 3.50 3.44 6.50
P 18.19 14.06 5.28 4.56 4.25 4.00 3.19 2.00 3.00 4.50 3.88 7.00
S 20.12 15.44 6.00 5.06 4.75 4.50 3.25 2.18 3.38 4.94 4.75 8.00
T 23.72 18.50 7.00 6.00 5.75 5.50 3.91 2.53 4.12 5.69 5.69 10.00

* Eye Hooks (3/4 TC - 22TA), Proof load is 2.5 times Working Load Limit. Eye Hooks (20 TC - 60TA), Proof Load is 2 times Working Load Limit.
All carbon hooks-average straightening load (ultimate load) is 5 times Working Load Limit. Alloy eye hooks 1 ton through 22 ton-average
straightening load (ultimate load) is 5 times Working Load Limit. Alloy eye hooks 30 tons through 60 tons-average straightening load (ultimate load)
is 4.5 times Working Load Limit.
† 3/4tC - 22tA dimensions shown are for S-4320 Latch Kits. Dimensions for sizes 20 ton carbon and larger are for PL Latch Kits.
†† Dimensions are for PL-N latch kits.

  • Forged - Quenched and Tempered.
  • Swivel hooks are load rated.
  • Proper design, careful forging, and precision controlled quench and tempering gives maximum strength without excessive weight and bulk.
  • Low profile hook tip designed to utilize Crosby S-4320 or PL-N latch kit. Even years after purchase of the original hook, latch assemblies can be added.
  • Hoist hooks incorporate markings forged into the product which address two (2) QUIC-CHECK® features:
    • Deformation Indicators -- Two strategically placed marks, one just below the shank or eye and the other on the hook tip, which allows for a QUIC-CHECK® measurement to de- termine if the throat opening has changed, thus indicating abuse or overload.
    • Angle Indicators -- Indicates the maximum included angle which is allowed between two (2) sling legs in the hook. These indicators also provide the opportunity to approxi- mate other included angles between two sling legs.
  • Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.

This hook is a positioning device and is not intended to rotate under load.
Use in corrosive environment requires shank and nut inspection in accordance with ASME B30.10-1.2.1(b)(2)(c) 2000.

  • U.S. Patents 5,381,650 & 5,193,480 & 5,103,755 and foreign equivalents.
Working Load Limit (t)* Dimensions (in.) Rep. Latch Stock No.
Carbon Alloy S-322 CN Stock No. S-322 AN Stock No. Weight Each (lbs.) A B C D F G H J K L M O † R S AA Rep. Latch Stock No.
3/4 1 1048600 1048804 .75 2.00 .82 1.25 2.86 1.25 .73 .81 .93 .63 5.66 .63 .89 4.55 .38 1.50 1096325
1 1-1/2 1048609 1048813 1.25 2.50 1.31 1.50 3.15 1.38 .84 .94 .97 .71 6.71 .71 .91 5.37 .50 2.00 1096374
1-1/2 2 1048618 1048822 2.25 3.00 1.50 1.75 3.59 1.50 1.00 1.16 1.06 .88 7.75 .88 1.00 6.12 .63 2.00 1096421
2 3 1048627 1048831 2.30 3.00 1.50 1.75 4.00 1.62 1.13 1.31 1.19 .94 8.25 .94 1.09 6.50 .63 2.00 1096468
3 5 1048636 1048837 4.96 3.50 1.64 2.00 4.84 2.00 1.44 1.63 1.50 1.31 9.69 1.13 1.36 7.50 .75 2.50 1096515
5 7 1048645 1048854 10.29 4.56 2.29 2.50 6.28 2.50 1.81 2.06 1.78 1.66 12.47 1.44 1.61 9.63 1.00 3.00 1096562
7-1/2 11 1048654 1048865 19.40 5.00 2.53 2.75 7.54 3.00 2.25 3.63 2.41 1.88 14.75 1.63 2.08 11.37 1.13 4.00 1096609
10 15 1048663 1048877 23.25 5.62 2.48 3.12 8.34 3.25 2.59 2.94 2.62 2.19 16.40 1.94 2.27 12.25 1.25 4.00 1096657
15 22 1048672 1048886 47.00 7.10 3.76 4.10 10.34 4.25 3.00 3.50 3.41 2.69 21.34 2.38 3.02 16.71 1.50 5.00 1096704
30 1025688 70.50 7.10 3.76 4.10 13.62 5.00 3.61 4.63 4.00 3.00 23.25 3.00 3.25 18.01 1.50 6.50 1093716

* NOTE: Carbon swivel hooks .75tC-15tC: proof load is 2 times working load limit. Designed with a 5 to 1 design factor.
Alloy swivel hooks 1tA-22tA : proof load is 2.5 times working load limit. Designed with a 4.5 to 1 design factor.
Alloy swivel hook 30tA: proof load is 2 times working load limit. Designed with a 4 to 1 design factor.
† Dimensions for hooks 3/4 ton carbon thru 22 ton alloy are for S-4320 latch kits. Dimensions for hooks 30 ton alloy are for PL latch kit.

All SHUR-LOC® hooks have the following features:

  • Forged Alloy Steel - Quenched and Tempered.
  • Recessed trigger design is flush with the hook body, protecting the trigger from potential damage.
    • Easy to operate with enlarged thumb access.
  • Positive Lock Latch is Self-Locking when hook is loaded.
  • The SHUR-LOC® hook, if properly installed and locked, can be used for personnel lifting applications and meets the intent of OSHA Rule 1926.550 (g) (4) (iv) (B).

Eye Style incorporates these added features:

  • Individually Proof Tested to 2-1/2 times the Working Load Limit with certification.
  • Fatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles.
  • 25% stronger than Grade 80.
  • Suitable for use with Grade 100 and Grade 80 chain.
  • Designed with "Engineered Flat" to connect to S-1325 chain coupler.

SHUR-LOC® Hook Series with positive Locking Latch
S-1316 Eye Hook

Chain Size Dimensions (in.)
(in.) (mm) Working Load Limit(lbs.*) S-1316 Stock No. Weight Each (lbs.) A C D E J L AA
6 3200 1022896 .85 .78 3.95 .79 2.60 .63 1.14 1.50
1/4-5/16 7-8 5700 1022914 1.80 1.08 5.31 1.10 3.50 .81 1.48 2.00
3/8 10 8800 1022923 3.40 1.30 6.57 1.17 4.39 .94 2.21 2.50
1/2 13 15000 1022932 6.00 1.65 8.23 1.67 5.45 1.16 2.22 3.00
5/8 16 22600 1022941 15.1 2.20 10.06 2.04 6.56 1.50 2.65
3/4 18-20 35300 1022942 19.0 2.60 10.77 2.22 7.76 2.03 3.52
7/8 22 42700 1022943 28.0 2.87 12.49 2.45 8.75 2.20 3.83
1 26 59700 1022944 49.5 3.15 14.60 3.21 9.87 2.68 4.09

* Minimum Ultimate Load is 4 times the Working Load Limit.

S-318A SHUR-LOC® Shank Hooks

Chain Size Dimensions (in.)
(in.) (mm) S-318A Stock No. Frame Code Grade 80 Alloy Chain Working Load Limit (lbs.)* A† B C D E F G J L AA Weight Each (lbs.)
6 1098101 D 2500 .79 2.16 3.31 .79 2.60 .67 6.26 .63 1.16 1.50 1.00
1/4-5/16 7-8 1098112 G 4500 1.00 2.40 4.16 1.10 3.51 .87 7.66 .81 1.48 2.00 1.99
3/8 10 1098123 H 7100 1.14 2.95 5.14 1.17 4.39 1.10 9.26 .94 1.83 2.50 3.56
1/2 13 1098134 I 12000 1.34 3.35 6.31 1.67 5.49 1.26 11.33 1.16 2.22 3.00 7.00
5/8 16 1098145 J 18100 1.63 3.94 7.28 2.04 6.55 1.50 13.26 1.50 2.65 3.50 16.00

* Ultimate Load is 4 times the Working Load Limit.
† Dimension before machining (as forged).

Alloy Master Links

  • Alloy Steel — Quenched and Tempered.
  • Individually Proof Tested to values shown, with certification.
  • Proof Tested with fixture sized to prevent localized point loading per ASTM A952. Consult Crosby for appropriate fixture size.
  • Crosby A-342 products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Sizes from 1/2" to 2" are drop forged and have a Product Identification Code (PIC) for material traceability, along with the size, the name Crosby and USA in raised lettering.
  • Selected sizes designated with "W" in the size column have enlarged inside dimensions to allow additional room for sling hardware and crane hook.
  • Incorporates patented QUIC-CHECK® deformation indicators.

A-342 Alloy Master Links

Size Dimensions (in.)
(in.) (mm) A-342 Stock No. Weight Each (lbs.) Working Load Limit (lbs.)* Proof Load (lbs.)** A B C Deformation Indicator
1/2W 13W 1014266 1.3 7400 17200 .62 2.80 5.00 3.50
5/8 16 1014280 1.5 9000 18000 .62 3.00 6.00 3.50
3/4W 19W 1014285 2.0 12300 28400 .73 3.20 6.00 4.00
7/8W 22W 1014319 3.3 15200 35200 .88 3.75 6.38 4.50
1W 26W 1014331 6.1 26000 60000 1010 4.30 7.50 5.50
1-1/4W 32W 1014348 12.0 39100 90400 1.33 5.50 9.50 7.00
1-1/2W 38W 1014365 18.6 61100 141200 1.61 5.90 10.50 7.50
1-3/4 44 1014388 25.2 84900 169800 1.75 6.00 12.00 7.50
2 51 1014404 37.0 102600 205200 2.00 7.00 14.00 9.00
‡ 2-1/4 ‡ 57 1014422 54.1 143100 289200 2.25 8.00 16.00
‡ 2-1/2 ‡ 63 1014468 67.8 160000 320000 2.50 8.00 16.00
‡ 2-3/4 ‡ 70 1014440 87.7 216900 433800 2.75 9.50 16.00
‡ 3 ‡ 76 1014486 115 228000 456000 3.00 9.00 18.00
‡ 3-1/4 ‡ 83 1014501 145 262200 524400 3.25 10.00 20.00
‡ 3-1/2 ‡ 89 1014529 200 279000 558000 3.50 12.00 24.00
‡ 3-3/4 ‡ 95 1015051 198 336000 672000 3.75 10.00 20.00
‡ 4 ‡ 102 1015060 228 373000 746000 4.00 10.00 20.00
‡ 4-1/4 ‡ 108 1015067 302 354000 708000 4.25 12.00 24.00
‡ 4-1/2 ‡ 114 1015079 345 360000 720000 4.50 14.00 28.00
‡ 4-3/4 ‡ 121 1015088 436 389000 778000 4.75 14.00 28.00
‡ 5 ‡ 127 1015094 516 395000 790000 5.00 15.00 30.00

* Ultimate Load is 5 times the Working Load Limit. Applications with wire rope and synthetic sling generally require a design factor of 5. ** Proof Test Load equals or exceeds the requirement of ASTM A952(8.1) and ASME B30.9. †† Welded Master Link.

A-345 Master Link Assembly
with Engineered Flat for use with S-1325 coupler link.

Size Dimensions (in.)
(in.) (mm) A-345 Stock No. Weight Each (lbs.) Working Load Limit Based on 5:1 Design Factor (lbs.)* Proof Load (lbs.)** A B C D E F G Deformation Indicator
3/4W 19W 1014739 3.5 12300 28400 .73 3.20 6.00 .56 3.35 1.77 .30 4.00
7/8W 22W 1014742 4.8 15200 35200 .88 3.75 6.38 .56 3.35 1.77 .30 4.50
1W 26W 1014766 9.3 26000 60000 1.10 4.30 7.50 .75 3.94 2.36 .33 5.50
1-1/4W 32W 1014779 15.8 39100 90400 1.33 5.50 9.50 1.00 6.30 3.54 .51 7.00
1-1/2W 38W 1014807 34.1 61100 141200 1.61 5.90 10.50 1.25 7.09 3.94 .65 7.50
1-3/4 44 1014814 46.7 84900 169800 1.75 6.00 12.00 1.38 8.00 5.00 .73 7.50
2 51 1014832 67.2 102600 205200 2.00 7.00 14.00 1.50 9.00 5.75 9.00
2-1/2 64 1014850 142 160000 320000 2.50 8.00 16.00 2.00 14.00 7.00
2-3/4 70 1014859 196 216900 433800 2.75 9.50 16.00 2.25 16.00 8.00
4 102 1014995 403 373000 746000 4.00 10.00 20.00 2.75 16.00 9.50

* Ultimate Load is 5 times the Working Load Limit. Applications with wire rope and synthetic sling generally require a design factor of 5. ** Proof Test Load equals or exceeds the requirement of ASTM A952(8.1) and ASME B30.9.

Open Swage Sockets

  • Forged from special bar quality carbon steel, suitable for cold forming.
  • Swage Socket terminations have an efficiency rating of 100% based on the catalog strength of wire rope.
  • Hardness controlled by spheroidize annealing.
  • Stamp for identification after swaging without concern for fractures (as per directions in National Swaging Brochure).
  • Swage sockets incorporate a reduced machined area of the shank which is equivalent to the proper "After Swage" dimension. Before swaging, this provides for an obvious visual difference in the shank diameter. After swaging, a uniform shank diameter is created allowing for a QUIC-CHECK® and permanent visual inspection opportunity.
    • Designed to quickly determine whether the socket has been through the swaging operation and assist in field inspections, it does not eliminate the need to perform standard production inspections which include gauging for the proper "After Swage" dimensions or proof loading.
  • U.S. Patent 5,152,630 and foreign equivalents.

NOTE: S-501 Swage Sockets are recommended for use with 6 x 19 or 6 x 37, IPS or XIP (EIP), XXIP (EEIP), RRL, FC or IWRC wire rope. Before using any National Swage fitting with any other type lay, construction or grade of wire rope, it is recommended that the termination be destructive tested and documented to prove the adequacy of the assembly to be manufactured. In accordance with ASME B30.9, all slings terminated with swage sockets shall be proof loaded.*

S-501
Open Swage Sockets

S-501 Open Socket Specifications Press / Die Data
Rope Size* Before Swage Dimensions (in.) Stock No. Side Load
S-501 Stock No. (in.) (mm) Weight Each (lbs.) A B C D E F H L M N Max. After Swage Dim. (in.) Die Description 500
1000
1500
Ton
5 x 7
1500
3000
Ton
6 x 12
1500
Ton
6 x 12
3000
Ton
6 x 12
1039021 1/4 6 .52 4.78 .50 1.38 .69 .27 2.19 .69 4.00 .38 1.47 .46 1/4 Socket 1192845
1039049 5/16 8 1.12 6.30 .78 1.62 .81 .34 3.25 .80 5.34 .48 1.67 .71 5/16-3.8 Socket 1192863
1039067 3/8 9-10 1.30 6.30 .78 1.62 .81 .41 3.25 .80 5.34 .48 1.67 .71 5/16-3/8 Socket 1192863
1039085 7/16 11-12 2.08 7.82 1.01 2.00 1.00 .49 4.31 1.00 6.69 .56 1.96 .91 7/16-1/2 Socket 1192881
1039101 1/2 13 2.08 7.82 1.01 2.00 1.00 .55 4.31 1.00 6.69 .56 1.96 .91 7/16-1/2 Socket 1192881
1039129 9/16 14 4.67 9.54 1.27 2.38 1.19 .61 5.38 1.25 8.13 .68 2.21 1.16 9/16-5/8 Socket 1192907
1039147 5/8 16 4.51 9.54 1.27 2.38 1.19 .68 5.38 1.25 8.13 .68 2.21 1.16 9/16-5/8 Socket 1192907
1039165 3/4 18-20 7.97 11.61 1.56 2.75 1.38 .80 6.44 1.50 10.00 .78 2.69 1.42 3/4 Socket 1192925
1039183 7/8 22 11.52 13.37 1.72 3.13 1.63 .94 7.50 1.75 11.63 .94 3.20 1.55 7/8 Socket 1192943
1039209 1 24-26 17.80 15.47 2.00 3.69 2.00 1.07 8.63 2.00 13.38 1.07 3.68 1.80 1 Socket 1192961
1039227 1-1/8 28 25.25 17.35 2.25 4.06 2.25 1.19 9.75 2.25 15.00 1.19 4.18 2.05 1-1/8 Socket 1192989
1039245 1-1/4 32 35.56 19.20 2.53 4.50 2.50 1.34 10.81 2.50 16.50 1.27 4.64 2.30 1-1/4 Socket 1193005
1039263 1-3/8 34-36 43.75 21.10 2.81 5.25 2.50 1.46 11.88 2.41 18.13 1.46 5.25 2.56 1-3/8 Socket 1193023
1039281 1-1/2 38-40 58.50 23.17 3.08 5.50 2.75 1.59 12.94 3.00 19.75 1.65 5.70 2.81 1-1/2 Socket 1193041 1191267 1195355 1195192
1039307 1-3/4 44 88.75 26.70 3.40 6.25 3.50 1.87 15.06 3.50 23.00 2.07 6.67 3.06 1-3/4 Socket 1193069 1191276 1195367 1195209
1042767 2 48-52 146.2 31.15 3.94 7.80 3.75 2.12 17.06 4.00 26.75 1.81 8.19 3.56 2 Socket 1193087 1191294 1195379 1195218

* Maximum Proof Load shall not exceed 50% of XXIP rope catalog breaking strength.

Closed Swage Sockets

  • Forged from special bar quality carbon steel, suitable for cold forming.
  • Swage Socket terminations have an efficiency rating of 100% based on the catalog strength of wire rope.
  • Hardness controlled by spheroidize annealing.
  • Stamp for identification after swaging without concern for fractures (as per directions in National Swaging Brochure).
  • Swage sockets incorporate a reduced machined area of the shank which is equivalent to the proper "After Swage" dimension. Before swaging, this provides for an obvious visual difference in the shank diameter. After swaging, a uniform shank diameter is created allowing for aQUIC-CHECK® and permanent visual inspection opportunity.
    • Designed to quickly determine whether the socket has been through the swaging operation and assist in field inspections, it does not eliminate the need to perform standard production inspections which include gauging for the proper "After Swage" dimensions or proof loading.
  • U.S. Patent 5,152,630 and foreign equivalents.

NOTE: S-502 Swage Sockets are recommended for use with 6 x 19 or 6 x 37, IPS or XIP (EIP), XXIP (EEIP), RRL, FC or IWRC wire rope. Before using any National Swage fitting with any other type lay, construction or grade of wire rope, it is recommended that the termination be destructive tested and documented to prove the adequacy of the assembly to be manufactured. In accordance with ASME B30.9, all slings terminated with swage sockets shall be proof loaded.*

S-502
Closed Swage Sockets

S-502 Closed Socket Specifications Press / Die Data
Rope Size* Before Swage Dimensions (in.) Stock No. Side Load
S-502 Stock No. (in.) (mm) Weight Each (lbs.) A B C D E F H L Max. After Swage Dim. (in.) Die Description 500
1000
1500
Ton
5 x 7
1500
3000
Ton
6 x 12
1500
Ton
6 x 12
3000
Ton
6 x 12
1039325 1/4 6 .33 4.28 .50 1.38 .76 .27 2.19 .50 3.50 .46 1/4 Socket 1192845
1039343 5/16 8 .75 5.42 .77 1.62 .88 .34 3.25 .68 4.50 .71 5/16-3/8 Socket 1192863
1039361 3/8 9-10 .72 5.42 .78 1.62 .88 .41 3.25 .68 4.50 .71 5/16-3/8 Socket 1192863
1039389 7/16 11-12 1.42 6.88 1.01 2.00 1.07 .49 4.31 .87 5.75 .91 7/16-1/2 Socket 1192881
1039405 1/2 13 1.42 6.88 1.01 2.00 1.07 .55 4.31 .87 5.75 .91 7/16-1/2 Socket 1192881
1039423 9/16 14 2.92 8.59 1.27 2.38 1.28 .61 5.38 1.14 7.25 1.16 9/16-5/8 Socket 1192907
1039441 5/8 16 2.85 8.59 1.27 2.38 1.28 .68 5.38 1.14 7.25 1.16 9/16-5/8 Socket 1192907
1039469 3/4 18-20 5.00 10.25 1.56 2.88 1.49 .80 6.44 1.33 8.63 1.42 3/4 Socket 1192925
1039487 7/8 22 6.80 11.87 1.72 3.12 1.73 .94 7.50 1.53 10.09 1.55 7/8 Socket 1192943
1039502 1 24-26 10.40 13.56 2.00 3.62 2.11 1.07 8.63 1.78 11.50 1.80 1 Socket 1192961
1039520 1-1/8 28 14.82 15.03 2.25 4.00 2.37 1.19 9.75 2.03 12.75 2.05 1-1/8 Socket 1192989
1039548 1-1/4 32 21.57 16.94 2.53 4.50 2.62 1.34 10.81 2.25 14.38 2.30 1-1/4 Socket 1193005
1039566 1-3/8 34-36 28.54 18.59 2.81 5.00 2.62 1.46 11.88 2.29 15.75 2.56 1-3/8 Socket 1193023
1039584 1-1/2 38-40 38.06 20.13 3.08 5.38 2.87 1.59 12.94 2.56 17.00 2.81 1-1/2 Socket 1193041 1191267 1193355 1195192
1039600 1-3/4 44 51.00 23.56 3.40 6.25 3.63 1.87 15.06 3.08 20.00 3.06 1-3/4 Socket 1193069 1191276 1195367 1195209
1042589 2 48-52 89.25 27.13 3.94 7.25 3.88 2.12 17.06 3.31 23.00 3.56 2 Socket 1193087 1191294 1195379 1195218

* Maximum Proof Load shall not exceed 50% of XXIP rope catalog breaking strength.

Eye & Eye Turnbuckles

  • End fittings are Quenched and Tempered, bodies heat treated by normalizing.
  • Hot Dip galvanized steel.
  • Turnbuckle eyes are forged elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckle sizes 1/4" through 2-1/2", a shackle one size smaller can be reeved through eye.
  • Modified UNJ thread on end fittings for improved fatigue properties. Body has UNC threads.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
  • Lock Nuts available for all sizes.
  • Fatigue Rated.

HG-226
Eye & Eye

Dimensions (in.)
Thread Dia. & Take Up (in.) HG-226 Working Load Limit (lbs.) Weight Each (lbs.) A J
Open
K
Closed
M
Open
N
Closed
R S X
Closed
BB
† 1/4 x 4 1031252 500 0.29 0.25 11.94 7.94 12.38 8.38 .81 .34 1.76 4.07
† 5/16 x 4-1/2 1031270 800 0.48 0.31 13.92 9.42 14.48 9.98 .95 .44 2.20 4.58
† 3/8 X 6 1031298 1200 0.75 0.38 17.56 11.56 18.24 12.24 1.13 .53 2.48 6.10
1/2 X 6 1031314 2200 1.72 0.5 19.94 13.94 20.82 14.82 1.41 .71 3.56 6.03
1/2 X 12 1031350 2200 2.93 0.5 32.23 20.23 33.11 21.11 1.41 .71 3.54 12.36
5/8 X 6 1031378 3500 2.75 0.63 21.72 15.72 22.72 16.72 1.80 .88 4.35 6.03
5/8 X 12 1031412 3500 4.12 0.52 34.06 22.06 35.06 23.06 1.80 .88 4.34 12.39
3/4 X 6 1031430 5200 4.22 0.75 23.24 17.24 24.50 18.50 2.09 1.00 5.12 6.13
3/4 X 12 1031476 5200 6.12 0.75 35.64 23.64 36.90 24.90 2.09 1.00 2.09 12.59
3/4 X 18 1031494 5200 7.83 0.75 47.64 29.64 48.90 30.90 2.09 1.00 5.12 18.53
7/8 X 12 1031519 7200 8.83 0.88 36.70 24.7 38.20 26.20 2.38 1.25 5.79 12.16
7/8 X 18 1031537 7200 11.5 0.88 49.17 31.17 50.67 32.67 2.38 1.25 5.79 18.63
1 X 6 1031555 10000 9.62 1.00 26.24 20.24 28.00 22.00 3.00 1.43 6.50 6.18
1 X 12 1031573 10000 13 1.00 38.24 26.24 40.00 28.00 3.00 1.43 6.50 12.18
1 X 18 1031591 10000 16.3 1.00 50.24 32.24 52.00 34.00 3.00 1.43 6.50 18.18
1 X 24 1031617 10000 20.2 1.00 62.84 38.84 64.60 40.60 3.00 1.43 6.47 24.84
1-1/4 X 12 1031635 15200 19.9 1.25 42.14 30.14 44.38 32.38 3.59 1.82 8.49 12.06
1-1/4 X 18 1031653 15200 23.8 1.25 54.14 36.14 56.38 38.38 3.59 1.82 8.49 18.06
1-1/4 X 24 1031671 15200 27.8 1.25 66.70 42.7 68.94 44.94 3.59 1.82 8.49 24.62
1-1/2 X 12 1031699 21400 28.7 1.50 44.24 32.24 46.74 34.74 4.09 2.12 9.46 12.32
1-1/2 X 18 1031715 21400 34.1 1.50 56.24 38.24 58.74 40.74 4.09 2.12 9.46 18.32
1-1/2 X 24 1031733 21400 39.6 1.50 68.86 44.86 71.36 47.36 4.09 2.12 9.46 24.94
1-3/4 X 18 1031779 28000 50.7 1.75 57.38 39.38 60.38 42.38 4.65 2.38 9.97 18.37
1-3/4 X 24 1031797 28000 58.2 1.75 69.38 45.38 72.38 48.38 4.65 2.38 9.97 24.37
2 X 24 1031813 37000 83.5 2.00 75.68 51.68 79.18 55.18 5.81 2.69 13.03 24.48
2-1/2 X 24 1031831 60000 149 2.50 79.18 55.18 83.18 59.18 6.49 3.12 13.76 24.60
2-3/4 X 24 1031859 75000 174 2.75 81.34 57.34 85.84 61.84 7.00 3.25 15.09 24.65

* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.
†Mechanical Galvanized

Jaw & Eye Turnbuckles

  • End fittings are Quenched and Tempered, bodies heat treated by normalizing.
  • Hot Dip galvanized steel.
  • Turnbuckles eyes are forged and elongated, by design, to maximize easy attachment in system and minimize stress in the eye. For turnbuckles size 1/4" through 2-1/2", a shackle one size smaller can be reeved through eye.
  • Forged jaw ends are fitted with bolts and nuts for 1/4" through 5/8", and pins and cotters on 3/4" through 2-3/4" sizes.
  • Modified UNJ thread on end fittings for improved fatigue properties.
  • Body has UNC threads.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • TURNBUCKLES RECOMMENDED FOR STRAIGHT OR IN-LINE PULL ONLY.
  • Lock Nuts available for all sizes.
  • Fatigue Rated.
Dimensions (in.)
Thread Dia. & Take Up (in.) HG-227 Stock No. Working Load Limit (lbs.)* Weight Each (lbs.) A B E
Closed
G J
Open
K
Closed
M
Open
N
Closed
R S X
Closed
BB
† 1/4 x 4 1031877 500 .33 .25 .45 1.66 .64 11.57 7.57 12.28 8.28 .81 .34 1.76 4.07
† 5/16 x 4-1/2 1031895 800 .52 .31 .50 2.02 .87 13.50 9.00 14.30 9.80 .95 .44 2.20 4.58
† 3/8 X 6 1031911 1200 .80 .38 .53 2.11 .85 16.91 10.91 17.87 11.87 1.13 .53 2.48 6.10
1/2 X 6 1031939 2200 1.77 .50 .64 3.22 1.07 19.30 13.30 20.48 14.48 1.41 .71 3.56 6.03
1/2 X 9 1031957 2200 2.25 .50 .64 3.20 1.07 25.59 16.59 26.77 17.77 1.41 .71 3.54 9.36
1/2 X 12 1031975 2200 2.67 .50 .64 3.20 1.07 31.59 19.59 32.77 20.77 1.41 .71 3.54 12.36
5/8 X 6 1031993 3500 2.98 .63 .79 3.90 1.32 20.73 14.73 22.27 16.27 1.80 .88 4.35 6.03
5/8 X 9 1032019 3500 3.72 .63 .79 3.89 1.32 27.07 18.07 28.61 19.61 1.80 .88 4.34 9.39
5/8 X 12 1032037 3500 4.35 .63 .79 3.89 1.32 33.07 21.07 34.61 22.61 1.80 .88 4.34 12.39
3/4 X 6 1032055 5200 4.51 .75 .97 4.71 1.52 22.17 16.17 24.09 18.09 2.09 1.00 5.12 6.13
3/4 X 9 1032073 5200 5.56 .75 .97 4.68 1.52 28.57 19.57 30.49 21.49 2.09 1.00 5.09 9.59
3/4 X 12 1032091 5200 6.42 .75 .97 4.68 1.52 34.57 22.57 36.49 24.49 2.09 1.00 5.09 12.59
3/4 X 18 1032117 5200 8.14 .75 .97 4.71 1.52 46.57 28.57 48.49 30.49 2.09 1.00 5.12 18.53
7/8 X 12 1032135 7200 9.10 .88 1.16 5.50 1.77 35.68 23.68 37.91 25.91 2.38 1.25 5.79 12.16
7/8 X 18 1032153 7200 11.6 .88 1.16 5.50 1.77 48.15 30.15 50.38 32.38 2.38 1.25 5.79 18.63
1 X 6 1032171 10000 10.0 1.00 1.34 6.09 2.05 25.03 19.03 27.59 21.59 3.00 1.43 6.50 6.18
1 X 12 1032199 10000 13.4 1.00 1.34 6.09 2.05 37.03 25.03 39.59 27.59 3.00 1.43 6.50 12.18
1 X 18 1032215 10000 16.7 1.00 1.34 6.09 2.05 49.03 31.03 51.59 33.59 3.00 1.43 6.50 18.18
1 X 24 1032233 10000 20.6 1.00 1.34 6.06 2.05 61.63 37.63 64.19 40.19 3.00 1.43 6.47 24.84
1-1/4 X 12 1032251 15200 20.9 1.25 1.84 8.09 2.82 70.76 28.76 43.98 31.98 3.59 1.82 8.49 12.06
1-1/4 X 18 1032279 15200 24.8 1.25 1.84 8.09 2.82 52.76 34.76 55.98 37.98 3.59 1.82 8.49 18.06
1-1/4 X 24 1032297 15200 28.8 1.25 1.84 8.09 2.82 65.32 41.32 68.51 44.54 3.59 1.82 8.49 24.62
1-1/2 X 12 1032313 21400 30.6 1.50 2.06 8.93 2.81 42.50 30.50 16.21 34.21 4.09 2.12 9.46 12.32
1-1/2 X 18 1032331 21400 36.0 1.50 3.06 8.93 2.81 54.50 36.50 58.21 40.21 4.09 2.12 9.46 18.32
1-1/2 X 24 1032359 21400 41.5 1.50 3.06 8.93 2.81 37.12 43.12 40.83 46.83 4.09 2.12 9.46 24.94
1-3/4 X 18 1032395 28000 52.1 1.75 2.60 9.36 3.35 55.37 37.37 59.77 41.77 4.65 2.38 9.97 18.37
1-3/4 X 24 1032411 28000 59.7 1.75 2.60 9.36 3.35 67.37 43.37 71.77 47.77 4.65 2.38 9.97 24.37
2 X 24 1032439 37000 89.9 2.00 2.62 11.80 3.74 72.66 18.66 77.95 53.95 5.81 2.69 13.03 24.48
2-1/2 X 24 1032457 60000 158 2.50 3.06 13.26 4.44 76.08 52.08 82.68 58.68 6.49 3.12 13.76 24.60
2-3/4 X 24 1032475 75000 187 2.75 3.69 14.92 4.19 78.05 54.05 85.67 61.67 7.00 3.25 15.09 24.65

* Proof Load is 2.5 times the Working Load Limit. Ultimate Load is 5 times the Working Load Limit.
†Mechanical Galvanized

US-422T Utility Wedge Sockets

  • Basket is cast steel.
  • Wedge socket terminations have an efficiency rating of 80% based on the catalog strength of XXIP wire rope.
  • Wedges are color coded for easy identification.
    • Blue - largest wire line size for socket.
    • Black - mid size wire line for socket.
      • 7/16" on US4
      • 9/16" on US5
    • Orange - smallest wire line size for socket.
  • Cast into each socket is the name "McKissick", "Crosby" or "CG", its model number and its wire line range.
  • By simply changing out the wedge, each socket can be utilized for various wire line sizes (Ensure correct wedge is used for wire rope size).
  • Cast into each wedge is the model number of the socket and the wire line size for which the wedge is to be used.
  • Load pin is forged and headed on one end.
  • US-422T wedge sockets contain a hammer pad (lip) to assist in proper securement of termination.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identifi- cation, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • UWO-422T Wedges are to be used only with the US-422T Wedge Socket Assemblies.

US-422T Utility Wedge Socket

Wire Rope Size Dimensions (in.)
Model No. (in.) (mm) US-422T Stock No. Weight Each (lbs.) Wedge Only Stock No. Weight Each (lbs.) A B C D G H J K L P R S T U V
US4T 3/8 10 1044300 4.6 1047310 .6 6.81 3.55 1.00 1.00 1.63 2.81 8.43 1.38 1.06 1.94 .50 2.53 .44 1.91 2.14
US4T 7/16 11 1041309 4.6 1047301 .6 6.81 3.55 1.00 1.00 1.63 2.81 8.73 1.08 1.06 1.94 .50 2.53 .53 1.76 1.88
US4T 1/2 13 1044318 4.6 1047329 .6 6.81 3.55 1.00 1.00 1.63 2.81 8.73 1.02 1.06 1.94 .50 2.53 .53 1.76 1.88
US5T 1/2 13 1044327 8.5 1047338 1.0 9.19 4.23 1.41 1.25 2.13 3.31 11.19 1.84 1.50 3.00 .63 3.25 .75 1.92 2.16
US5T 9/16 14 1044336 8.5 1047347 1.0 9.19 4.23 1.41 1.25 2.13 3.31 11.47 2.40 1.50 3.00 .63 3.25 .69 2.00 2.18
US5T 5/8 16 1044345 8.5 1047356 1.0 9.19 4.23 1.41 1.25 2.13 3.31 11.47 2.34 1.50 3.00 .63 3.25 .69 2.00 2.18
US6T 5/8 16 1044354 9.4 1047365 1.4 9.45 4.7 1.50 1.25 2.24 3.63 11.91 2.48 1.50 3.00 .56 3.25 .88 2.38 2.75
US6T 3/4 19 1044363 9.4 1047374 1.4 9.45 4.7 1.50 1.25 2.24 3.63 11.81 2.03 1.50 3.00 .56 3.25 .88 2.13 2.63
US8AT 5/8 16 1044372 19.8 1047383 4.3 10.59 5.68 1.81 1.63 2.38 5.53 13.19 1.91 1.53 2.88 .75 4.13 .69 3.26 3.50
US8AT 3/4 19 1044381 20.4 1047392 4.8 10.59 5.68 1.81 1.63 2.38 5.84 13.54 2.38 1.53 2.88 .75 4.13 .78 3.12 3.38
US7* 7/8 22 1038580 16.5 1046674 2.6 11.26 5.11 1.31 1.25 2.69 2.56 1.63 3.26 .66 3.25 1.06 2.12 2.56
US7* 1 25 1038589 16.5 1046683 2.6 11.26 5.11 1.31 1.25 2.69 2.56 1.63 3.26 .66 3.25 1.06 1.88 2.38
US8T 7/8 22 1044404 31.5 1047425 7.6 12.77 6.96 1.81 1.63 3.06 7.2 16.02 2.87 1.65 3.12 .75 4.13 .88 3.88 4.18
US8T 1 25 1044417 32.5 1047431 8.6 12.77 6.96 1.81 1.63 3.06 7.31 16.41 2.32 1.65 3.12 .75 4.13 1.03 3.76 4.06
US10T 1-1/8 28 1044426 55.4 1047440 12.5 15.94 8.62 1.81 1.63 3.57 9.15 19.72 3.26 2.19 4.38 .75 4.13 1.09 4.76 5.06
US10T 1-1/4 32 1044435 58.0 1047459 15.0 15.94 8.62 1.81 1.63 3.57 9.39 20.22 2.83 2.19 4.38 .75 4.13 1.19 4.62 4.94
US11T 1-1/8 28 1044444 60.6 1047468 12.5 16.34 8.73 2.62 2.50 3.56 9.15 19.97 3.37 2.34 4.50 1.06 6.13 1.09 4.76 5.06
US11T 1-1/4 32 1044453 64.9 1047477 15.0 16.34 8.73 2.62 2.50 3.56 9.39 20.48 2.91 2.34 4.50 1.06 6.13 1.19 4.62 4.94

* Non-"TERMINATOR"™ Style

S-421T Wedge Sockets

  • Wedge socket terminations have an efficiency rating of 80% based on the catalog strength of XXIP wire rope.
  • Crosby products meet or exceed all requirements of ASME B30.26 including identifi- cation, ductility, design factor, proof load and temperature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • Type Approval and certification in accordance with ABS 2006 Steel Vessel Rules 1-1-17.7, and ABS Guide for Certification of Cranes.
  • Individually magnetic particle inspected.
  • Pin diameter and jaw opening allows wedge and socket to be used in conjuction with closed swage and spelter sockets.
  • Secures the tail or "dead end" of the wire rope to the wedge, thus eliminates loss or "Punch out" of the wedge.
  • Eliminates the need for an extra piece of rope, and is easily installed.
  • The TERMINATOR™ wedge eliminates the potential breaking off of the tail due to fatigue.
  • The tail, which is secured by the base of the clip and the wedge, is left undeformed and available for reuse.
  • Incorporates Crosby’s patented QUIC-CHECK® "Go" and "No-Go" feature cast into the wedge. The proper size rope is determined when the following criteria are met:
    • 1) The wire rope should pass thru the "Go" hole in the wedge.
    • 2) The wire rope should NOT pass thru the "No-Go" hole in the wedge.
  • Utilizes standard Crosby Red-U-Bolt® wire rope clip.
  • The 3/8" thru 1-1/8" standard S-421 wedge socket can be retrofitted with the new style TERMINATOR™ wedge.
  • Available with Bolt, Nut, and Cotter Pin.
  • U.S. patent 5,553,360, Canada patent 2,217,004 and foreign equivalents.

S-421T Wedge Sockets
Assembly includes Socket, Wedge, Pin and Wire Rope Clip

<
Wire Rope Dia. Optional G-4082
(in.) (mm) S-421T Stock No. Weight Each (lbs.) S-421 TW Stock No. Wedge Only Wedge Only Weight Each (lbs.) G-4082 Stock No. Weight Each (lbs.)
3/8 9-10 1035000 3.18 1035555 .50 1092227 .38
1/2 11-13 1035009 6.15 1035564 1.05 1092236 .69
5/8 14-16 1035019 9.70 1035573 1.79 1092254 1.15
3/4 18-19 1035027 14.50 1035582 2.60 1092281 1.91
7/8 20-22 1035036 21.50 1035591 4.00 1092307 3.23
1 24-26 1035045 30.75 1035600 5.37 1092325 5.40
1-1/8 28 1035054 45.30 1035609 7.30 1092343 7.50
1-1/4 30-32 1035063 64.90 1035618 10.60 1092372 10.34
Wire Rope Dia. Dimensions (in.)
(in.) (mm) S-421T Stock No. A B C D G H J* K* L P R S T U V
3/8 9-10 1035000 5.69 2.72 .81 .81 1.38 3.06 7.80 1.88 .88 1.56 .44 2.13 .44 1.25 1.38
1/2 11-13 1035009 6.88 3.47 1.00 1.00 1.62 3.76 8.91 1.26 1.06 1.94 .50 2.56 .53 1.75 1.88
5/8 14-16 1035019 8.25 4.30 1.25 1.19 2.12 4.47 10.75 1.99 1.22 2.25 .56 3.25 .69 2.00 2.19
3/4 18-19 1035027 9.88 5.12 1.50 1.38 2.44 5.28 12.36 2.41 1.40 2.63 .66 3.63 .78 2.34 2.56
7/8 20-22 1035036 11.25 5.85 1.75 1.63 2.69 6.16 14.37 2.48 1.67 3.13 .75 4.31 .88 2.69. 2.94
1 24-26 1035045 12.81 6.32 2.00 2.00 2.94 6.96 16.29 3.04 2.00 3.75 .88 4.70 1.03 2.88 3.28
1-1/8 28 1035054 14.38 6.92 2.25 2.25 3.31 7.62 18.34 2.56 2.25 4.25 1.00 5.44 1.10 3.25 3.56
1-1/4 30-32 1035063 16.34 8.73 2.62 2.50 3.56 9.39 20.48 2.94 2.34 4.50 1.06 6.13 1.19 4.62 4.94

* Nominal

NOTE: For intermediate wire rope sizes, use next larger size socket.

Swivel Hoist Ring

Color coded to distinguish between UNC (Red) and Metric (Silver) thread types.

U.S. Patent 5,352,056

  • Available in UNC and Metric thread sizes.
    • UNC threads available in sizes from 800 pounds to 100,000 pounds Working Load Limit, with a design factor of 5 to 1.
    • Metric threads available in sizes from 400kg to 16,900kg and dual rated in both a 4 to 1 and 5 to 1 design factor.
  • All Components are Alloy Steel - Quenched and Tempered.
  • Rated at 100% at 90° angle.
  • 100% individually proof tested to 2-1/2 times the Working Load Limit with certification and Statistically Magnetic Particle inspected. (Can be furnished 100% Magnetic Particle inspected when requested at time of order.)
  • Each product has a Product Identification Code (PIC) for material traceability along with a Working Load Limit and the name Crosby or “CG” stamped into it.
  • Crosby products meet or exceed all the requirements of ASME B30.26 including identification, ductility, design factor, proof load and temper- ature requirements. Importantly, Crosby products meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
  • 360° swivel and 180° pivot action.
  • Fatigue rated to 20,000 cycles at 1-1/2 times the Working Load Limit.
  • Individually packaged along with proper application instructions and warning information.
  • Bolt is secured with E-clip, threads are grooved. This method allows for easy disassembly and assembly of hoist ring for thorough examination of all components. Replacement kits are available.
  • Bolts are individually Proof Tested.
  • Multiple Bolt length available to meet specific application requirements.
  • Zinc Plated (Yellow Chromate) finish for increased corrosion protection thru 30,000 pounds size.

UNC Swivel Hoist Rings

  • Top washer has the following features:
    • The Working Load Limit and Recommended Torque value are permanently stamped into each washer.
    • Washer is color coded for easy identification: Red - UNC thread.
  • Individually Proof Tested to 2-1/2 times Working Load Limit.
  • Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A 574. All threads listed are UNC.
  • BOLT SIZE IDENTIFICATION: The size of the bolt will be stated as in the drawing below. Illus- tration shows meaning of each dimension given.
  • Frame 2 and larger are RFID EQUIPPED.
Dimensions (in.)
Frame Size No. HR-125 Stock No. Working Load Limit (lbs.)* Torque in Ft. Lbs. Bolt Size A ‡ Effective Thread Projection Length B C D Radius E Diameter F G H Weight Each (lbs.)
1 † 1016887 800 7 5/16 - 18 x 1.50 0.58 2.72 0.97 0.46 0.34 1.87 1.12 0.37
1 † 1016898 1000 12 3/8 - 16 x 1.50 0.58 2.72 0.97 0.46 0.34 1.87 1.05 0.39
2 1016909 2500 28 1/2 - 13 x 2.00 0.70 4.85 1.96 0.87 0.69 3.35 2.29 2.33
2 † 1016912 2500 28 1/2 - 13 x 2.50 1.20 4.85 1.96 0.87 0.69 3.35 2.29 2.36
2 1016920 4000 60 5/8 - 11 x 2.00 0.70 4.85 1.96 0.87 0.69 3.35 2.16 2.41
2 † 1016924 4000 60 5/8 - 11 x 2.75 1.45 4.85 1.96 0.87 0.69 3.35 2.16 2.47
2 1016931 5000 100 3/4 - 10 x 2.25 0.95 4.85 1.96 0.87 0.69 3.35 2.04 2.52
2 † 1016935 5000 100 3/4 - 10 x 2.75 1.45 4.85 1.96 0.87 0.69 3.35 2.04 2.59
3 1016942 7000 ** 100 3/4 - 10 x 2.75 0.89 6.57 2.96 1.36 0.94 4.87 2.97 6.72
3 † 1016946 7000 ** 100 3/4 - 10 x 3.50 1.64 6.57 2.96 1.36 0.94 4.87 2.97 6.81
3 1016953 8000 160 7/8 - 9 x 2.75 0.89 6.57 2.96 1.36 0.94 4.87 2.84 6.84
3 † 1016957 8000 160 7/8 - 9 x 3.50 1.64 6.57 2.96 1.36 0.94 4.87 2.84 6.96
3 1016964 10000 230 1 - 8 x 3.00 1.14 6.57 2.96 1.36 0.94 4.87 2.72 7.09
3 † 1016969 10000 230 1 - 8 x 4.00 2.14 6.57 2.96 1.36 0.94 4.87 2.72 7.31
4 1016975 15000 470 1-1/4 - 7 x 4.50 2.21 8.72 3.71 1.19 1.19 6.18 3.93 14.51
5 1016986 24000 800 1-1/2 - 6 x 6.50 2.97 12.42 4.71 1.75 1.75 8.48 5.64 37.73
5 1016997 30000 1100 2 - 4-1/2 x 6.50 2.97 12.42 4.71 1.75 1.75 8.48 5.14 40.69
6 1017001 50000 2100 2-1/2 - 4 x 8.0 4.00 16.88 5.75 2.25 2.25 11.00 8.03 88.00
7 1017005 75000 4300 3 - 4 x 10.5 5.00 19.50 7.25 2.75 2.75 14.16 8.5 166.00
8 1017009 100000 5100 3-1/2 - 4 x 13.0 # 7.00 22.09 7.75 3.25 3.25 15.91 9.28 265.00

* Ultimate Load is 5 times the Working Load Limit.
** Ultimate Load is 4.5 times the Working Load Limit for 7000# Hoist Ring when tested in 90 degree orientation.
† Long Bolts are designed to be used with soft metal (i.e., aluminum) work piece. While the long bolts may also be used with ferrous metal
(i.e.,steel & iron) work piece, short bolts are designed for ferrous work pieces only.
‡ Bolt specification is a Grade 8 Alloy socket head cap screw to ASTM A 574.
l # Hex head bolt used on Frame 8 (100,000lb.) Hoist Ring.